Keep your home flowing and jammin’ with the DropStars crew!
Give us a call at 818-275-7114 or book online today.
Your 3-Step Guide to Rockstar-Level Plumbing Service
Get on the Setlist
Call or book online to reserve your service slot and secure your backstage pass to hassle-free plumbing.
Tune the Soundcheck
Our techs arrive right on time, walk you through the issue, and hit you with clear, upfront pricing before striking a single chord.
Crank Up the Volume
We bring the noise (and the know-how) with clean, lasting repairs that keep your home running in perfect harmony.
Water Heater Maintenance in Burbank, CA
In Burbank, consistent hot water is essential, but most homeowners only think about their water heater when it fails. Unfortunately, neglecting routine maintenance is the fastest way to shorten your unit’s lifespan, degrade its efficiency, and trigger an expensive emergency breakdown.
At DropStars Plumbing, we service both traditional tank and modern tankless systems across Burbank and the San Fernando Valley. Our preventative check-ups eliminate harmful sediment, verify every critical safety component, and keep your system running at peak efficiency — so you get reliable hot water and no surprise replacement bills.
Our Fans know who brings the noise
Why Routine Water Heater Maintenance Is Critical
What Burbank Water Does to Your Water Heater

Burbank has very hard water, which can have a major impact on water heaters over time. According to Burbank Water and Power’s latest published water-quality data, Burbank water averaged approximately 285 parts per million of hardness, or 16.6 grains per gallon. The U.S. Geological Survey classifies anything above 180 ppm as very hard water.
Burbank ultimately relies on imported water purchased from the Metropolitan Water District of Southern California. BWP also uses groundwater credits to store imported water in the local aquifer, pump it back through Burbank wells, treat it and blend it into the city’s drinking-water supply.
What Does That Mean for Your Water Heater?
Hard water contains higher concentrations of calcium and magnesium. As water is repeatedly heated, those minerals can form scale and sediment inside the tank, on heating surfaces and throughout the hot-water system. The USGS specifically notes that hard water can form scale in water heaters and pipes.
In the Burbank homes we service, sediment buildup is something we pay particular attention to, especially on water heaters that have gone several years without maintenance. Over time, excessive buildup can contribute to rumbling or popping noises, reduced hot-water performance and additional stress on the water heater.
For that reason, we generally recommend annual water-heater flushing in Burbank along with periodic inspection of the anode rod and the overall condition of the system.
How Long Should a Water Heater Last in Burbank?
A traditional tank water heater typically has an expected service life of approximately 8 to 12 years, although water quality, installation, usage and maintenance can significantly affect that number. A.O. Smith specifically identifies local water quality and maintenance history as factors that affect water-heater lifespan.
Because Burbank’s water measures around 16.6 grains per gallon, regular maintenance becomes especially important. Once a tank reaches around 10 years old, we recommend having its condition evaluated rather than simply waiting for the tank to fail.
Do You Need a Permit to Replace a Water Heater in Burbank?
Yes. The City of Burbank requires a plumbing permit for water-heater replacement. Water heaters are classified as Tier 1 permits, meaning a standard replacement generally does not require plan check and can be obtained through Burbank’s streamlined permit process.
For FY 2026–27, Burbank lists a $77.52 plumbing permit issuance fee plus an $88.40 water-heater fee, before any other applicable City fees or transaction charges.
Routine maintenance such as flushing or servicing an existing water heater does not involve replacing the unit and generally does not require a water-heater replacement permit.
Our Tank Water Heater Maintenance Checklist
Complete tank flush and sediment removal
We shut off the gas or power and the cold water supply, attach hoses, and methodically drain the full tank volume, forcing out accumulated sediment and mineral deposits through the drain valve.
Thorough flushing removes the hard scale layer responsible for rumbling and popping, letting the burner or heating elements transfer heat directly into the water again. You get faster recovery and lower gas or electric use.
Sacrificial anode rod inspection and replacement
We locate and remove the existing anode rod — the component designed to attract corrosion away from the steel tank interior, sacrificing itself so the tank survives.
If the rod is significantly worn, pitted, or reduced to less than a quarter-inch of steel core — common after 3–5 years in hard water — we install a new factory-spec magnesium or aluminum/zinc rod. We show you the old rod so you can see exactly what we’re basing that on.
Critical safety and component checks
Temperature and Pressure (T&P) relief valve testing. We physically test the valve to confirm it opens, releases pressure, and reseats — verifying the safety function is intact rather than seized.
Gas burner and venting check (gas units). We inspect the burner assembly for rust, clear debris, and check the flue and vent piping for proper draft and complete combustion — which is what prevents carbon monoxide hazards.
Heating element and wiring test (electric units). We test amperage draw and continuity across the elements and wiring, confirming efficient heating and tight electrical connections.
Thermostat calibration. We verify the thermostat is holding the recommended 120°F — hot enough for household use, cool enough to limit scald risk and slow scale formation.
This multi-point process addresses both ways tank heaters fail: mechanical breakdown and structural decay.
Specialized Tankless Water Heater Maintenance

Tankless units don’t collect sediment the way tank heaters do, but they’re far more vulnerable to scale forming inside the heat exchanger — and clearing it takes a chemical flush, not a drain.
Heat exchanger descaling (acid flush)
Tankless units push high water volume across a compact heat exchanger, so mineral scale accumulates on the exchanger walls quickly. We connect an approved pump system and circulate a safe, non-toxic descaling solution through the exchanger, dissolving hard scale and restoring both heating efficiency and flow rate.
Inlet water filter and screen cleaning
We remove and clean the inlet filters and screens that protect the heat exchanger from debris, restoring unobstructed flow into the unit.
Burner and ignition assembly check
We inspect and clean the gas burner, ignition components, and the Category III stainless venting, confirming the unit ignites quickly and combusts completely and safely.
Code compliance check
We verify the installation meets current Burbank and California requirements — venting materials, gas pressure, and drain clearances.
Tankless units are precision equipment. Skipping the descaling interval causes reduced hot water output, flow restriction, and eventually a failed heat exchanger, which is the single most expensive part of the unit.
Why Burbank Homeowners Choose DropStars
Licensed and certified specialists. Our technicians are fully licensed — California license #1113528 — and trained on all major tank and tankless manufacturers.
We show you the proof. You see the state of the anode rod and the sediment we pull out. We recommend replacement based on what’s in front of you, not on a script.
Local and prompt. We’re based on Victory Blvd in Burbank, not dispatching from across the county. Scheduled service that respects your time.
Built around longevity. The goal isn’t just getting hot water back today — it’s protecting the unit against the corrosion and sediment damage that forces premature replacement.
Schedule Your Water Heater Maintenance in Burbank
Protect your investment, lower your utility bills, and keep reliable hot water year-round. Don’t let sediment and corrosion quietly shorten your system’s life.
Call DropStars Plumbing at (818) 275-7114 or book online to schedule your water heater maintenance in Burbank, CA. We’re available Monday through Saturday, 24 hours, with emergency service when you need it.
Frequently Asked Questions (FAQs)
Annually for tank units in Burbank. In softer-water regions you can stretch it, but local hardness makes yearly the right interval here. Tankless units need a descaling flush every 12–18 months.
Partly. A homeowner can drain and flush a tank with a garden hose, and it’s better than doing nothing. What a DIY flush doesn’t cover is anode rod inspection, T&P valve testing, burner and venting inspection, and thermostat calibration — which is where the safety issues and the early warning signs actually show up. It also won’t satisfy a manufacturer asking for professional service records.
If it’s worn past roughly a quarter-inch of remaining core, yes. Once the rod is spent, corrosion moves to the tank itself, and a corroded tank can’t be repaired — only replaced. A rod costs a fraction of a new water heater.
Most manufacturers require documented annual professional maintenance. We provide a service record you can produce if you ever file a claim.
Usually, yes. Rumbling is almost always sediment: water trapped under the sediment layer boils and forces its way through. A full flush typically resolves it. If the noise persists after a flush, the sediment has hardened onto the tank bottom, which usually means the unit is near end of life.
Ask An Expert
Contact Form
"*" indicates required fields